Micro-Module Responder that adds INSTEON control to existing motorised projector screens, motorised blinds / shutters, motorised curtains and more. Dual-pole mains power operation.
View the Insteon Micro Motor Controller on the Insteon integration diagram
- Control motorised projector screens, window shutters, blinds
- Manual control retained via a connected, hard-wired switch
- Compatible with latching and single/dual momentary switches
Want to add wireless remote control to your automated window shutters, blinds and projector screens? INSTEON makes it easy. The Micro Motor Controller is the first INSTEON device designed specifically for up/down and open/close motor-controlled appliances. By including this module as a part of your INSTEON home automation network, you will enjoy remote control of your shutters, blinds, screens and more. This compact module installs behind your existing switch, giving it full INSTEON automation while retaining local control at the switch by way of sense wires. The patented INSTEON dual-band communication reliably sends signals over existing electrical wires (powerline) in your home and via radio frequency (RF). The micro-module motor controller is so tiny that it can even be installed as an in-line module within a fixture box, and you can then control it from any INSTEON controller, providing remote control without running wires to a wall switch.
The INSTEON micro range also includes a Micro Dimmer and a Micro Relay (On/Off).
General |
� |
| Product Name: | INSTEON Micro Motor Controller |
| Product Code: | 2444-522 |
| Regions: | Australia and New Zealand |
| In the box: | INSTEON Micro Motor Controller |
INSTEON |
� |
| INSTEON Powerline Mesh Repeater: | Yes |
| INSTEON RF Mesh Repeater: | Yes |
| INSTEON Controller: | Yes |
| INSTEON Responder: | Yes |
| Maximum links/scenes: | 400 |
| Load brightness levels: | 32 locally (256 with software) |
| Status LED: | Green / On, Red / Off, Blinks green or red during setup, Blinks red to indicate traffic (must be enabled via software) |
| LED brightness: | Adjustable from off to 100% bright |
| Beep on button press: | Beeps red to indicate traffic (must be enabled via software) |
| Local control: | Yes |
| Commands supported as controller: | On / Off, Fast On / Fast Off, Begin brighten / End brighten, Begin dim / End dim |
| Commands supported as responder: | Open (On) / Close (Off), Begin raise (brighten) / / Begin lower (dim), End raise (brighten) / End lower (dim), Beep |
| Software configurable: | Yes |
| RF range: | Up to 50 meters feet open air |
| Phase detect beacon: | Yes |
| X10 support: | Yes |
| X10 addresses: | Any 1 of 256 (unassigned by default) |
| INSTEON device category: | 0x0E Window Coverings |
| INSTEON device subcategory: | AUS / NZ (921.0 Mhz), 0x32 |
Mechanical |
� |
| Mounting: | Behind switch or outlet, or above light fixture in single-gang electrical box | Casing: | UV stabalized plastic (INSTEON White) | Wire connections: | Sense 1 (yellow): 24 AWG, 0.205mm�, Sense 2 (purple): 24 AWG, 0.205mm� | Max. wire size: | 4mm�, 12 AWG (2.72mm diameter) | Min. cable size: | 1.5mm�, 15 AWG | Screw clamp connections: | Line, Load 1 (up), Load 2 (down), Neutral | Set button: | Yes | Beeper: | Yes | Beep on button press: | Optional (off by default) | LED: | 1 RGB |
| Dimensions: | 46.6mm W x 17.5mm H x 46.6mm D |
| Weight: | 72g |
| Operating Conditions: | Indoors, 0� C to 40� C, up to 90% relative humidity |
Electrical |
� |
| Voltage: | 100VAC to 240VAC (� 10%) |
| Frequency: | 50/60Hz auto-detected at power-up |
| Max. load: | 8A resistive, 3A motor |
| Load types: | Resistive, Inductive/capacitive, Low voltage halogen, motor |
| Hardwired remote control: | Yes, either latching or momentary switches supported |
| User replaceable fuse: | N/A |
| Retain all settings without power: | Yes, saved in non-volatile EEPROM |
| Standby power consumption: | <1W |
| Safety approved: | Approved for use in Australia and New Zealand |
| Certifications: | AS/NZS 4268, CISPR 22, IEC 60669-2-1 |
