Micro-sized on/off INSTEON responder that adds control to a switched appliance or non-dimmable lighting zone. Installs behind a light switch.
View the Insteon Micro Relay (On/Off) on the Insteon integration diagram
- Wires in behind your existing switches or fixtures
- Retain manual control via a connected, hard-wired switch
- Compatible with latching and single/dual momentary switches
Insteon Responder
Appliance Control
Dual-mesh technology
Contractor Installation
Adding remote control to wired lights usually means replacing switches, not any more. With INSTEON's new dual-band micro-module relay, you can keep your existing antique, toggle or decorative wall switches while adding the customisable, remote control functionality that INSTEON offers.
This compact module installs behind your existing switch, giving it full INSTEON automation while retaining local control at the switch by way of sense wires. Connect the sense wires to any style wall switch to match any type of designer theme (antique, push-button, metal, etc.). The micro-module relay can also be installed as an in-line module within a fixture box, providing remote control without having to run wires to a wall switch.
The INSTEON micro range also includes a Micro Dimmer for lighting and a Micro Motor Controller for projection screens, shutters, curtains, blinds, etc.
General |
� |
| Product Name: | INSTEON Micro Relay (On/Off) |
| Product Code: | 2443-522 |
| Regions: | Australia and New Zealand |
| In the box: | INSTEON Micro Relay (On/Off) |
INSTEON |
� |
| INSTEON Powerline Mesh Repeater: | Yes |
| INSTEON RF Mesh Repeater: | Yes |
| INSTEON Controller: | Yes |
| INSTEON Responder: | Yes |
| Maximum links/scenes: | 400 |
| Status LED: | Green / On, Red / Off, Blinks green or red during setup, Blinks red to indicate traffic (must be enabled via software) |
| LED brightness: | Adjustable from off to 100% bright |
| Beep on button press: | Beeps red to indicate traffic (must be enabled via software) |
| Local control: | Yes |
| Commands supported as controller: | On / Off, Fast On / Fast Off, Begin brighten / End brighten, Begin dim / End dim |
| Commands supported as responder: | On / Off, Fast On / Fast Off, Beep |
| Software configurable: | Yes |
| RF range: | Up to 50 meters feet open air |
| Phase detect beacon: | Yes |
| X10 support: | Yes |
| X10 addresses: | Any 1 of 256 (unassigned by default) |
| INSTEON device category: | 0x02 Switched Lighting Control |
| INSTEON device subcategory: | AUS / NZ (921.0 Mhz), 0x32 |
Mechanical |
� |
| Mounting: | Behind switch or outlet, or above light fixture in single-gang electrical box | Casing: | UV stabalized plastic (INSTEON White) | Wire connections: | Sense 1 (yellow): 24 AWG, 0.205mm�, Sense 2 (purple): 24 AWG, 0.205mm� | Max. wire size: | 4mm�, 12 AWG (2.72mm diameter) | Min. cable size: | 1.5mm�, 15 AWG | Screw clamp connections: | Line, Load 1, Load 1 (second terminal), Neutral | Set button: | Yes | Beeper: | Yes | Beep on button press: | Optional (off by default) | LED: | 1 RGB |
| Dimensions: | 46.6mm W x 17.5mm H x 46.6mm D |
| Weight: | 72g |
| Operating Conditions: | Indoors, 0� C to 40� C, up to 90% relative humidity |
Electrical |
� |
| Voltage: | 100VAC to 240VAC (� 10%) |
| Frequency: | 50/60Hz auto-detected at power-up |
| Max. load: | 10A, 3600W/240VAC resistive, 700W/240VAC inductive/capacitive, 2000W/240VAC bulbs/low voltage halogen |
| Load types: | Resistive, Inductive/capacitive, Low voltage halogen |
| User replaceable fuse: | N/A |
| Retain all settings without power: | Yes, saved in non-volatile EEPROM |
| Standby power consumption: | <1W |
| Safety approved: | Approved for use in Australia and New Zealand |
| Certifications: | AS/NZS 4268, CISPR 22, IEC 60669-2-1 |
Products similar to the Insteon Micro Relay (On/Off) :
Micro Motor Controller
Micro-Module Responder that adds INSTEON control to existing motorised projector screens, motorised blinds / shutters, motorised curtains and more. Dual-pole mains power operation.
DIN-Rail Relay (On/Off)
Inline On/Off Responder that adds INSTEON control to a fixed on/off appliance or non-dimmable lighting zone. Requires installation by a qualified electrical contractor.
