INSTEON Plug-In Dimmer

  $69.00

  • Code: IN2632-522
  • Product manual
  • Delivery costs

Add INSTEON control to a plug-in dimmable light up to 300W. Features an adjustable ramp rate, preset dim level and local control. Can be controlled by any INSTEON controller.

View the INSTEON Plug-In Dimmer on the INSTEON integration diagram

  • Control a plug-in light with INSTEON
  • Works with dimmable loads up to 300 Watts max
  • Suitable for incandescent lights and dimmable transformers

Insteon Responder
Dimmable
32 Dimming Steps
Dual-mesh technology
Plug and Play
2-Year Warranty

The simplest option for adding INSTEON control to your plug-in lamps.

The INSTEON Plug-In Dimmer (Dual-Band) is a full-featured plug-in dimmer that can be remotely controlled by any INSTEON controller. This simple-to-use plug-in dimmer has advanced features, including:

  • Adjustable ramp rate that slowly brings the lamp on
  • Preset dim level that stores your preferred choice of 32 brightness levels when turning the lamp on
  • Retain local, manual control via a control switch on the module

Installation is easy, simply plug the module into a power point and then connect a lamp or other light fitting up to 300W max into the module. You'll then have control of the light from any INSTEON Controller, including automated control, scenes, or control over the web via your computer or smartphone.

This product is not suitable for fluorescent, low-energy lights or appliances as attempting to dim these devices may damage the module or your device. For these applications, use the INSTEON Plug-In Relay (On/Off) module, or other type of INSTEON relay module.

General

Product Name: INSTEON Plug-In Dimmer
Product Code: 2632-522
Regions: Australia and New Zealand
In the box: INSTEON Plug-In Dimmer
Warranty: 2 Years

INSTEON

INSTEON Powerline Mesh Repeater: Yes
INSTEON RF Mesh Repeater: Yes
INSTEON Controller: Yes
INSTEON Responder: Yes
Maximum links/scenes: 400
Load brightness levels: 32 locally (256 with software)
Status LED: Green / On, Red / Off, Blinks green or red during setup, Blinks red to indicate traffic (must be enabled via software)
LED brightness: Adjustable from off to 100% bright
Local on-level: Adjustable from 32 fixed brightness levels or resume dim
Local ramp rate: Adjustable from 0.1 second to 5 seconds locally (0.1 seconds to 8 minutes with software)
Beep on button press: Beeps red to indicate traffic (must be enabled via software)
Commands supported as controller: On / Off, Fast On / Fast Off, Begin brighten / End brighten, Begin dim / End dim
Commands supported as responder: On / Off, Fast On / Fast Off, Begin brighten / End brighten, Begin dim / End dim, Incremental brighten / Incremental dim, Beep
Software configurable: Yes
RF range: Up to 50 meters feet open air
Phase detect beacon: Yes
X10 support: Yes
X10 addresses: Any 1 of 256 (unassigned by default)
INSTEON device category: 0x01 dimmable lighting control
INSTEON device subcategory: AUS / NZ (921.0 Mhz), 0x12

Mechanical

Mounting: Standard AC power outlet
Casing: UV stabalized plastic (INSTEON White)
Set button: Yes
Beeper: Yes
Beep on button press: Optional (off by default)
LED: 1 RGB
Dimensions: 43mm W x 108mm H x 35mm D
Weight: 130g 10g
Operating Conditions: Indoors, 0 C to 40 C, up to 90% relative humidity

Electrical

Voltage: 100VAC to 240VAC ( 10%)
Frequency: 50/60Hz auto-detected at power-up
Max. load: 300 W at 240VAC
Load types: Lighting: Incandescent, dimmable LED, dimmable CFL, dimmable halogen
User replaceable fuse: Yes
Retain all settings without power: Yes, saved in non-volatile EEPROM
Standby power consumption: <0.75W
Safety approved: Approved for use in Australia and New Zealand
Certifications: AS/NZS 4268, CISPR 22, IEC 60669-2-1

Products similar to the INSTEON Plug-In Dimmer:


Micro Relay (On/Off)

Micro-sized on/off INSTEON responder that adds control to a switched appliance or non-dimmable lighting zone. >


Micro Dimmer

Dimmable Micro-Module Responder that adds INSTEON control to overhead lights. Installs behind a light switch.